Bulletpro Elite 5.5T 2 Post Lift (STD-6255TD)
Looking for a 2 post hoist for sale that suits cars, vans and utes?
The Bulletpro Elite 5.5T 2 Post Lift (STD-6255TD) is a versatile all-rounder with twin direct-drive hydraulic rams and 3-stage telescopic arms.
Supplied across SA, NT and WA by HDL Auto Equip.
STD-6255TD- 5.5 tonne capacity
- Low lift pad height of 106mm, max lift height 1949mm
- Pad extensions (80mm and 180mm) and arm extensions (250mm) included
- 24v low-voltage controls, automatic arm locks and single point safety lock release
Description
Description
Bulletpro Elite 5.5T 2 Post Lift (STD-6255TD)
Looking for a 2 post hoist for sale that can handle almost anything coming through your workshop? The Bulletpro Elite 5.5T 2 Post Lift (model STD-6255TD) is a genuine all-rounder, built to lift a huge variety of cars, vans and pick-up trucks. It is supplied by HDL Auto Equip across South Australia, the Northern Territory and Western Australia.
A 2 post hoist for sale that suits most workshops
Most workshops do not service just one type of vehicle. One hour it is a small hatch, the next it is a dual-cab ute or a van. With a 5.5 tonne capacity, this 2 post car hoist gives you room to move across a wide range of work without needing a different lift for each job.
The Elite uses twin direct-drive hydraulic rams and 3-stage symmetrical telescopic arms, so you get a wide reach range to position the vehicle’s lift points correctly. Arms run from 820mm minimum out to 1700mm, and up to 1950mm with the arm extensions fitted.
Key features of the Bulletpro Elite 5.5T
- 5.5 tonne lifting capacity
- Twin direct-drive hydraulic rams
- 3-stage symmetrical telescopic arms (820mm to 1700mm, up to 1950mm with extensions)
- Low lift pad height of 106mm, with a maximum lift height of 1949mm
- Double-thread adjustable lift pads
- Includes 2 sets of lift pad extensions (80mm and 180mm) and arm extensions (250mm)
- 24v low-voltage control system
- Automatic arm locks
- Single point safety lock release
- Foam covered roof protection cut-out
- Three post height settings: 5200mm, 5320mm and 5420mm
- CE marked
Built around practical, everyday use
A low lift pad height of 106mm helps you get under lower vehicles, while the supplied pad extensions (80mm and 180mm) and arm extensions (250mm) help you reach the correct lift points on taller utes and vans. The double-thread adjustable pads let you fine-tune the contact height, and the foam covered roof protection cut-out is a thoughtful touch to help protect the top of the vehicle.
On the safety side, the automatic arm locks and single point safety lock release keep operation straightforward, and the 24v low-voltage control system keeps the controls simple. It is a good fit for general servicing, tyres and brakes, suspension and driveline work.
If you have been searching for a quality Bulletpro hoist, this is the Elite model: solid, capable and versatile.
Who it suits
If you run an independent workshop, a tyre and mechanical shop or a dealership service bay, this 5.5 tonne 2 post hoist is worth a look. It handles everyday passenger cars as well as heavier vans and utes, which makes it a sensible choice when you want one dependable lift to cover most of your workload. Check your bay dimensions against the post spacing and overall width below before you order.
Specifications
| Model | Bulletpro Elite STD-6255TD |
| Capacity | 5.5 tonne |
| Lift system | Twin direct-drive hydraulic rams |
| Arms | 3-stage symmetrical telescopic, 820mm to 1700mm (up to 1950mm with extensions) |
| Low lift pad height | 106mm |
| Max lift height | 1949mm |
| Included extensions | Pad extensions 80mm and 180mm, arm extensions 250mm |
| Control system | 24v low voltage |
| Post height settings | 5200 / 5320 / 5420mm |
| Distance between posts | 2906mm |
| Overall width | 3500mm |
| Certification | CE marked |
